To determine the performance of the antenna simulation results, fabrication and soldering processes are needed. The soldering process is the process of connecting two or more materials using tin or metal by heating. In this paper, the soldering process is carried out to connect the 50? SMA connector to the feed line and ground. The results of the rejection of the frequency in the simulation results from the range 5.2 – 6.1 GHz. For rejection frequency before soldering is 4.8 – 7.1 GHz. And after soldering the rejection of frequencies from the 4.2 – 5.5 GHz. The bandwidth deviation before and after soldering on the lower band 600 MHz and high band 1600 MHz.
L. Liu, S. W. Cheung, and T. I. Yuk, “Compact MIMO antenna for portable devices in UWB applications,” IEEE Trans. Antennas Propag., vol. 61, no. 8, pp. 4257–4264, 2013, doi: 10.1109/TAP.2013.2263277.
T. Peter, R. Nilavalan, H. F. Abutarboush, and S. W. Cheung, “A novel technique and soldering method to improve performance of transparent polymer antennas,” IEEE Antennas Wirel. Propag. Lett., vol. 9, pp. 918–921, 2010, doi: 10.1109/LAWP.2010.2077271.
D. W. Astuti, M. Megahari, and D. Rusdiyanto, “Perancangan Antena Diplexing Menggunakan Metode Half Mode SIW dengan Metode Cavity Back Slot Sebagai Matching Impedansi,” vol. 11, no. 1, pp. 1–14, 2021.
D. A. NURMANTRIS, H. WIJANTO, and B. S. NUGROHO, “Optimasi Pattern Reconfigurable Antenna Bercelah Melingkar menggunakan Algoritma Genetika,” ELKOMIKA J. Tek. Energi Elektr. Tek. Telekomun. Tek. Elektron., vol. 8, no. 1, p. 111, 2020, doi: 10.26760/elkomika.v8i1.111.
M. I. Setiawan and J. Endri, “Rancang Bangun Antena Mikrostrip Path Rectangular pada Frekuensi 900 MHz untuk Aplikasi GSM,” J. Telekomun. Inf. Respati Fak. Sains dan Teknol. Univ. Respatii Yogyakarta, vol. XIV, 2019.
M. Pourvahab and G. Ekbatanifard, “An efficient forensics architecture in software-defined networking-IoT using blockchain technology,” IEEE Access, vol. 7, pp. 99573–99588, 2019, doi: 10.1109/ACCESS.2019.2930345.
Ramdani, M. Yunus, and E. Wismiana, “Merancang Dan Mengimplementasikan Antena Mikrostrip Beamwidth Antena Maksimum 10 0,” pp. 1–10, 2017.
H. Herudin, “Perancangan Antena Mikrostrip Frekuensi 2,6 GHz untuk Aplikasi LTE (Long Term Evolution),” Setrum Sist. Kendali-Tenaga-elektronika-telekomunikasi-komputer, vol. 1, no. 1, p. 41, 2016, doi: 10.36055/setrum.v1i1.469.
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Copyright Notice
An author who publishes in the Jurnal Elektro dan Telekomunikasi Terapan agrees to the following terms:
- Author retains the copyright and grants the journal the right of first publication of the work simultaneously licensed under the Creative Commons Attribution-NonCommercial 4.0 International License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal
- Author is able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book) with the acknowledgement of its initial publication in this journal.
- Author is permitted and encouraged to post his/her work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of the published work (See The Effect of Open Access).
Read more about the Creative Commons Attribution-NonCommercial 4.0 International License. here: http://creativecommons.org/licenses/by-nc/4.0/.
Privacy Statement
The names and email addresses entered in this journal site will be used exclusively for the stated purposes of this journal and will not be made available for any other purpose or to any other party.
